Quick answer

Verified

Applies toHandbook edition September 2014Handbook edition January 2015Handbook edition March 2015Handbook edition August 2015

Vauxhall’s handbook doesn’t print fuse ratings, so none is shown. Fit a replacement with the same rating as the fuse you remove — the handbook says: “Data on the replacement fuse must match the data on the defective fuse.”

Seat heating, driver

Fuse
27
Fuse box
Instrument panel
Location
The fuse box is located behind a cover in the glovebox.

Instrument panel/Seat heating/ FlexDock

Fuse
30
Fuse box
Instrument panel
Location
The fuse box is located behind a cover in the glovebox.

Seat heating, passenger

Fuse
32
Fuse box
Instrument panel
Location
The fuse box is located behind a cover in the glovebox.

Where is the fuse box?

Instrument panel fuse box

The fuse box is located behind a cover in the glovebox.

  1. Open the glovebox, then open the cover and fold it down.

We haven’t drawn a schematic of the instrument panel fuse box for this version yet. Use the fuse and relay numbers on this page and the legend on the fuse box to find the right position.

Where to look

  • 27

    The fuse box is located behind a cover in the glovebox.

    Fuse · Seat heating, driver

    Position not shown on the schematic. Find fuse 27 on the fuse box legend.

  • 30

    The fuse box is located behind a cover in the glovebox.

    Fuse · Instrument panel/Seat heating/ FlexDock

    Position not shown on the schematic. Find fuse 30 on the fuse box legend.

  • 32

    The fuse box is located behind a cover in the glovebox.

    Fuse · Seat heating, passenger

    Position not shown on the schematic. Find fuse 32 on the fuse box legend.

Always confirm the number against the legend on the fuse box cover before pulling anything.

How to replace the fuse safely

  1. Switch off the ignition and all electrical equipment. Take the key out, or move a keyless fob away from the car.
  2. Open the fuse box and find the fuse using the number on the cover legend or the chart on this page.
  3. Pull the fuse straight out with the plastic fuse puller (usually clipped inside the fuse box) or fine-nose pliers.
  4. Look at the metal strip inside the fuse. A broken or burnt strip means it has blown.
  5. Fit a new fuse with exactly the same amperage rating. The number on top and the colour should match.
  6. Refit the cover, switch on and test the component.
  • Never fit a fuse with a higher amperage rating than specified. It can let wiring overheat.
  • Never bridge a fuse with wire, foil or anything else.

Fuse keeps blowing?

A fuse that blows again straight away is doing its job. Something on that circuit is drawing too much current. Common causes are damaged wiring shorting to the bodywork, a failing motor or socket, water getting in, or a faulty accessory. Fitting fuse after fuse, or a bigger fuse, won’t fix the fault and can overheat the wiring. Have the circuit tested by an auto electrician.

Not the fuse? Check these next.

  • One seat or both?

    If only one seat has failed, its own fuse, switch or heating pad is the likely cause.

  • Connector under the seat

    The seat wiring plugs in under the seat. Sliding the seat can strain or loosen this connector.

  • Heating element

    Elements can break inside the cushion, often where you kneel or slide in and out of the car.

Sources & verification

Applies toHandbook edition September 2014

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toHandbook edition January 2015

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toHandbook edition March 2015

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toHandbook edition August 2015

Status
Verified
Specification
UK market
Last checked
14 October 2026

Fuse layouts can differ between trim levels and optional equipment. Always confirm against the legend on your fuse box.