Quick answer

Verified

Applies toType 1 passenger fuse box · Built 1 August 2009 to 28 February 2010Type 2 passenger fuse box · Built 1 August 2009 to 28 February 2010Type 1 passenger fuse box · Built 1 March 2010 to 20 June 2010Type 2 passenger fuse box · Built 1 March 2010 to 20 June 2010Type 1 passenger fuse box · Built 21 June 2010 to 6 February 2011Type 2 passenger fuse box · Built 21 June 2010 to 6 February 2011

High beam only: these are the circuits Ford labels for the high (main) beam. This answer does not cover the dipped (low) beam.

Main beam left-hand relay

Fuse
12
Amperage
10A
Fuse box
Engine compartment
Location
In the engine compartment

Main beam right-hand relay

Fuse
13
Amperage
10A
Fuse box
Engine compartment
Location
In the engine compartment

Main beam

Relay
R4
Fuse box
Engine compartment
Location
In the engine compartment

Where is the fuse box?

Engine compartment fuse box

In the engine compartment

Our source doesn’t describe how to open this fuse box. Check your owner’s handbook.

We haven’t drawn a schematic of the engine compartment fuse box for this version yet. Use the fuse and relay numbers on this page and the legend on the fuse box to find the right position.

Where to look

  • 12

    In the engine compartment

    Fuse ·10A · Main beam left-hand relay

    Position not shown on the schematic. Find fuse 12 on the fuse box legend.

  • 13

    In the engine compartment

    Fuse ·10A · Main beam right-hand relay

    Position not shown on the schematic. Find fuse 13 on the fuse box legend.

  • R4

    In the engine compartment

    Relay · Main beam

    Position not shown on the schematic. Find relay R4 on the fuse box legend.

Always confirm the number against the legend on the fuse box cover before pulling anything.

How to replace the fuse safely

  1. Switch off the ignition and all electrical equipment. Take the key out, or move a keyless fob away from the car.
  2. Open the fuse box and find the fuse using the number on the cover legend or the chart on this page.
  3. Pull the fuse straight out with the plastic fuse puller (usually clipped inside the fuse box) or fine-nose pliers.
  4. Look at the metal strip inside the fuse. A broken or burnt strip means it has blown.
  5. Fit a new fuse with exactly the same amperage rating. The number on top and the colour should match.
  6. Refit the cover, switch on and test the component.
  • Never fit a fuse with a higher amperage rating than specified. It can let wiring overheat.
  • Never bridge a fuse with wire, foil or anything else.

Checking the relay

  1. With the ignition off, pull the relay straight out of its socket. Rock it gently if it is tight.
  2. Relays rarely look damaged when they fail. To test, swap in an identical relay with the same part number from a non-essential circuit.
  3. If the fault moves to the other circuit, replace the relay. If it doesn’t, the problem is elsewhere.

Fuse keeps blowing?

A fuse that blows again straight away is doing its job. Something on that circuit is drawing too much current. Common causes are damaged wiring shorting to the bodywork, a failing motor or socket, water getting in, or a faulty accessory. Fitting fuse after fuse, or a bigger fuse, won’t fix the fault and can overheat the wiring. Have the circuit tested by an auto electrician.

Not the fuse? Check these next.

  • Blown bulb

    If only one side is out, a failed bulb is far more likely than a fuse. Check the bulb first.

  • Headlight switch or stalk

    If dipped and main beam behave differently, the switch or stalk may be at fault.

  • Relay or control module

    If both sides fail at the same moment, suspect a relay, the switch or the lighting control module.

  • Earth connection

    Dim or flickering lights often come from a corroded earth point rather than the fuse.

Sources & verification

Applies toType 1 passenger fuse box · Built 1 August 2009 to 28 February 2010

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toType 2 passenger fuse box · Built 1 August 2009 to 28 February 2010

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toType 1 passenger fuse box · Built 1 March 2010 to 20 June 2010

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toType 2 passenger fuse box · Built 1 March 2010 to 20 June 2010

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toType 1 passenger fuse box · Built 21 June 2010 to 6 February 2011

Status
Verified
Specification
UK market
Last checked
14 October 2026

Applies toType 2 passenger fuse box · Built 21 June 2010 to 6 February 2011

Status
Verified
Specification
UK market
Last checked
14 October 2026

Fuse layouts can differ between trim levels and optional equipment. Always confirm against the legend on your fuse box.