Quick answer

Verified

Applies toHandbook edition August 2018Handbook edition January 2019Handbook edition October 2019

Vauxhall’s handbook doesn’t print fuse ratings, so none is shown. Fit a replacement with the same rating as the fuse you remove — the handbook says: “Data on the replacement fuse must match the data on the defective fuse.”

Starter

Fuse
1
Fuse box
Engine compartment
Location
The fuse box is in the front left of the engine compartment.

Starter

Fuse
2
Fuse box
Engine compartment
Location
The fuse box is in the front left of the engine compartment.

Where is the fuse box?

Engine compartment fuse box

The fuse box is in the front left of the engine compartment.

  1. Disengage the cover and remove it.
  2. After having changed defective fuses, close the fuse box cover and press until it engages.
  3. If the fuse box cover is not closed correctly, malfunction may occur.
Engine compartmentCarFixData schematic
Engine compartment fuse box: map of 57 fuse positions, fuse 1 and 2 highlighted345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565712
These fusesOther fuse positionsNot usedOur own schematic, drawn from the fuse positions printed in Vauxhall’s handbook illustration of this fuse box. Not to scale and not a manufacturer drawing — always match the number on the fuse box before pulling a fuse.

Where to look

  • 1

    The fuse box is in the front left of the engine compartment.

    Fuse · Starter

    Highlighted on the engine compartment map.

  • 2

    The fuse box is in the front left of the engine compartment.

    Fuse · Starter

    Highlighted on the engine compartment map.

The map shows where each fuse sits. Always confirm the number against the legend on the fuse box cover before pulling anything.

How to replace the fuse safely

  1. Switch off the ignition and all electrical equipment. Take the key out, or move a keyless fob away from the car.
  2. Open the fuse box and find the fuse using the number on the cover legend or the chart on this page.
  3. Pull the fuse straight out with the plastic fuse puller (usually clipped inside the fuse box) or fine-nose pliers.
  4. Look at the metal strip inside the fuse. A broken or burnt strip means it has blown.
  5. Fit a new fuse with exactly the same amperage rating. The number on top and the colour should match.
  6. Refit the cover, switch on and test the component.
  • Never fit a fuse with a higher amperage rating than specified. It can let wiring overheat.
  • Never bridge a fuse with wire, foil or anything else.

Fuse keeps blowing?

A fuse that blows again straight away is doing its job. Something on that circuit is drawing too much current. Common causes are damaged wiring shorting to the bodywork, a failing motor or socket, water getting in, or a faulty accessory. Fitting fuse after fuse, or a bigger fuse, won’t fix the fault and can overheat the wiring. Have the circuit tested by an auto electrician.

Not the fuse? Check these next.

  • Battery charge

    Clicking, slow cranking or dim dash lights usually mean a flat battery, not a fuse.

  • Battery terminals

    Loose or corroded terminals can stop the starter even with a good battery.

  • Immobiliser

    A flashing security light can mean the key isn’t recognised. Try the spare key.

  • Clutch or gear selector switch

    Many cars only crank with the clutch fully pressed, or in Park/Neutral on automatics.

  • Starter motor or solenoid

    A single loud click with good battery voltage often points to the starter itself.

Sources & verification

Applies toHandbook edition August 2018

Status
Verified
Specification
UK market
Last checked
15 October 2026

Applies toHandbook edition January 2019

Status
Verified
Specification
UK market
Last checked
15 October 2026

Applies toHandbook edition October 2019

Status
Verified
Specification
UK market
Last checked
15 October 2026

Fuse layouts can differ between trim levels and optional equipment. Always confirm against the legend on your fuse box.